Download >>> https://tiurll.com/1vf96c
Q: I have a modem of my ISP installed at home I want to connect my WL-5460AP v2 to it, so need to connect one of the two Ethernet ports of the back of the WL-5460AP to the modem exit (Ethernet port).. In this case, please lower the MTU and MRU value to lower values (such as 1463, 1432, or 1400).. Check the BSS and do a site survey to select AP1 When an AP is in 'Access Point Client' mode, it will act as a wireless card.. If your AP does not support WDS function or you are trying to extend the distance of a wireless router.. A: AdHOC and Infrastructure are 2 ways to form the wireless network ADHOC (Peer To Peer): The wireless network are formed by wireless cards only.. It happens to non-AirLive products also You can test this syndrome by pressing 'Control-F5' to let the webpage reload when you can access the website.. Free Download AirLive WL-5450AP Access Point Firmware 3 2 1 3 9eu (Router / Switch / AP).. Infrastructure (Access Point): The wireless network are formed by Access Point and cards.. AirLive(歐立科技) is a well-known IP Surveillance Networking solutions which provide solutions both surveillance and network solution, products includes: Fiber Switch, Wireless Outdoor Network, IP Cameras, Megapixel IP Camera, Fisheye IP Camera, IVS IP Camera, Smar.. WEP adds data encryption to every single packet transmitted in the wireless network.. AP or wireless router serve as a hub for connections to the cards With Access Point, the users can connect to wired network device such as LAN, router, and internet.. Please follow the instruction below to extend In the diagram above, Computer B's distance is too far away from 'AP1' to make a wireless connection.. The biggest disadvantage for AdHoc mode is that no network device can be attached to the network directly, thus making connection to LAN and Internet difficult.. If pressing Control-F5 works, then it is very likely to be the case In this case, please reboot your machine in safe mode and runs a virus scan (make sure you have the latest virus definition).. Furthermore, AP allows access control and other security features AP also extend the range between the cards.. A: If your AP is equipped with WDS (Repeater) function, you can extend the distance by changing the software settings on the AP to WDS(Repeater) mode.. 168 0 ), but each with different IP address • Set AP2 at 'Access Point Client' mode in the advanced operation setting menu.. It is not recommended to use AdHOC except for small environment To work in AdHoc mode, the cards must be set to the same SSID(Network Name) and set to AdHoc(Peer To Peer) mode.. The 40bit and 64bit encryption are the same because of out 64 bits, 40 bits are private.. However, both AP must support WDS(Repeater) function Please follow the quick installation guide on the AP for instruction on WDS mode.. Only 1 IP address comes out of the modem, so the WL-5460AP needs to behave as router as well.. Please follow the steps below: • Unplug the power of WL-5460AP • Hold the reset button while plugging the power.. All AP and cards in a infrastructure network must use the same ESSID(Network Name) and setup to work in Infrastructure (Access Point) mode.. Do not release the reset button until the 'Status' LED goes off • Set your PC's IP address to 192.. A: Wired Equivalent Privacy (WEP) is the method for secure wireless data transmission.. 168 1 6' You should see the emergency code page where you can upload your AirLive firmware again.. • Now Computer A should be able to connect with Computer B A: There seems to be some virus or browser bug recently that is causing this issue.. Can it be done and if so, which settings do I need to select to:(1) Use it as a router (providing IP addresses to the multiple PC’s that want to connect to the WL-5460AP(2) Can I still also use the second Ethernet port to connect a wired PC to the WL-5460AP? A: Please check if your WL-5460AP's serial number is e5460AP70500001 or later.. Or reinstall your browser program Another possibility is the MTU and MRU value are set incorrectly with your ISP.. I want to connect my WL-5460AP v2 to it, so need to connect one of the two Ethernet ports of the back of the WL-5460AP to the modem exit (Ethernet port).. WDS allows an AP to connect with another WDS enabled AP wirelessly, and still able to communicate with WLAN cards at the same time.. Only 1 IP address comes out of the modem, so I have a modem of my ISP installed at home.. Conversely, 104 and 128 bit are the same. We can extend the wireless coverage by using 2 more APs to create a wireless repeater: • Place the 'AP2' and 'AP3' at a location that still have good signal reception from 'AP1' • Connect AP2 and AP3 together using crossover Ethernet cable.. If it is, it has emergency code function Otherwise, it doesn't Once you make sure it has emergency code function.. There is no access point or wireless router in the network Cards communicate directly with each other.. 168 1 199 Connect your PC to the WL-5460AP • Open your web browser, then type '192.. • Make sure all APs and cards are on the same IP subnet (for example, all start with 192.. In this case, AP2 connect to AP1 like a wireless card • Connect Computer B to AP3 wirelessly.
Comments